中国质量认证中心CQC国家授权强制性产品认证目录(CQC/PD014-2004)（第1版第2次修订）围认证依据的国家/行业标准对应的国际标准GB15934-1996IEC60799:1984电缆GB12972.1～.10-1991压3kV及车车辆用GB12528.1-1990JB8145-19950/750V绝缘电线GB5013.1～.7-1997JB8735.1～.3-1998IEC60245-1～-7:19940/750V乙烯绝缘GB5023.1～.7-1997JB8734.1～.5-1998IEC60227-1,-3:1993IEC60227-2,-5:1979IEC60227-4:1992IEC602277:19950/750V乙烯绝缘套软电缆面为?2，芯1芯）GB5023.5-1997聚氯乙烯绝缘聚氯乙烯护套软电缆补充要求挠性连接体标称截和1?2，～60GB5023.6-1997电梯电缆和挠性连接用电缆补充要求围认证依据的国家/行业标准对应的国际标准压3kV及烯烃绝缘辆用电缆GB12528.1-1990GB12528.11-2003---本文来源于网络，仅供参考，勿照抄，如有侵权请联系删除---用途器具GB17465.1-1998GB17465.2-1998IEC60320-1:1994IEC60320-2-2:1990用途插头GB2099.1-1996GB2099.2-1997GB1002-1996GB1003-1999IEC60884-1:1994IEC60884-2-2:1989用途固定的开关GB16915.1-2003IEC60669-1:1993GB9816-1998IEC60691:1993的管状熔GB9364.1-1997GB9364.2-1997GB9364.3-1997IEC60127-1:1988IEC60127-2:1989IEC60127-3:1988插座和耦GB11918-2001GB11919-2001IEC60309-1:1999IEC60320-2:1999用途器具GB17465.1-1998GB17465.2-1998IEC60320-1:1994IEC60320-2-2:1990用途固定电器附件GB17466-1998IEC60670:1989（移动式漏电继GB6829-1995JB8755-1998JB8756-1998IEC60755：1983IEC61540:1997保护的剩断路器GB16916.1-2003GB16916.21-1997GB16916.22-1997IEC61008-1:1996IEC61008-2-1:1990IEC61008-2-2:1990围认证依据的国家/行业标准对应的国际标准护的剩余路器GB16917.1-2003GB16917.21-1997GB16917.22-1997IEC61009-1:1996IEC61009-2-1:1991IEC61009-2-2:1991---本文来源于网络，仅供参考，勿照抄，如有侵权请联系删除---场所用的断路器GB10963-1999IEC60898:1995GB13539.1-2002GB13539.2-2002GB13539.3-1999GB13539.4-1992GB13539.6-2002GB13539.5-1999IEC60269-1:1998IEC60269-2:1986IEC60269-3:1987IEC60269-4:198IEC60269-2-1:2000IEC60269-3-1:1994GB14048.2-2001GB17701-1999IEC60947-2:1995IEC60934:1993隔离器、熔断器组GB14048.3-2002IEC60947-3:2001护装置限流护装置、热保护电器、低触器、电GB14048.2-2001GB14048.4-2003IEC60947-2:1995IEC60947-4-1:2000<电压GB14048.5-2001IEC60947-5-1:1997围认证依据的国家/行业标准对应的国际标准器开关、压力开关、脚敏开关、按钮开关、微动开关、温程开关、自动转换关GB14048.2-2001GB14048.3-2002GB14048.4-2003GB14048.5-2001GB/T14048.10-1999IEC60947-2:1995IEC60947-3:2001IEC60947-4-1:2000IEC60947-5-12:1992接触器、器、信号头组件、GB14048.5-2001GB14048.4-2003GB14048.6-1998GB17885-1999GB14048.9-1998IEC60947-5-1:1997IEC60947-4-1:2000IEC60947-4-2:1995IEC610952:1992---本文来源于网络，仅供参考，勿照抄，如有侵权请联系删除---交流半控制器和关设备GB7251.1-1997GB7251.2-1997GB7251.3-1997GB7251.4-1998GB7251.5-1998IEC60439-1:1992IEC60439-2:1987IEC60439-3:1990IEC60439-4:199机：功率下的电动GB12350-2000围认证依据的国家/行业标准对应的国际标准动机的同到1500大连续1.1千瓦GB14711-1993击电钻）GB3883.6-1991GB3883.1-1991GB4343-1995GB17625.1-2003IEC60745-2-1:1989,+A1:1992IEC60745-1:1982CISPR12:2001和冲击扳GB3883.2-1991IEC60745-2-2:1982+A1:1991含角向向砂轮磨、湿式磨、抛光光机)GB3883.3-1991IEC60745-2-3:1984,+A1:1995平板砂光光机、带GB3883.4-1991IEC60745-2-4:1983,+A1:1992,+A2:1995围认证依据的国家/行业标准对应的国际标准GB3883.5-1998IEC60745-2-5:1993镐）GB3883.7-1991GB3883.1-1991GB4343-1995GB17625.1-2003IEC60745-2-6:1989+A1:1992IEC60745-1:1982CISPR12:2001电喷枪GB3883.13-1992IEC60745-2-6:1989+A1:1992双刃电剪GB3883.8-1991IEC60745-2-8:1982+A1,...